Baby Rocking Chair Plans Site Youtube Com

🔥+ Baby Rocking Chair Plans Site Youtube Com 04 Aug 2020 How to Build a Hope Chest. Step 1: Assemble the Box. Assemble the box as shown in the picture using 1-1/2″ wood screws. Step 2: Add Rails for Shelf. Step 3: Assemble Top Rail. Step 4: Install Top Rail. Step 5: Add Trim. Step 6: Assemble Top. Step 7: Assemble Cedar Shelf. Step 8: Install Hinges, Bumpers and Top.

Baby Rocking Chair Plans Site Youtube Com ENDWALL BRACES-GAMBREL ROOF BARNS, HURRICANE AREAS, 5639, '48, 1. GABLEROOF BARN FRAMING, 34' & 36' WIDE, GLUED TRUSS RAFTER ...

Flip Top Vanity Table With Hot Drawers

Her Tool Belt

DIY furniture plans, crafts, and home improvement tutorials to empower you!

by Amy 5 Comments

I have been slowly trying to get my garage/workshop organized and easy to work in as a shared space. Two major things that I have issues with are storage and work space. I use this old table as an assembly table/ miter saw stand.  I am tired of pulling the heavy miter saw on and off the table and want a permanent spot for it. But since it’s my garage, it really does need to be mobile.

Baby Rocking Chair Plans Site Youtube Comhow to Baby Rocking Chair Plans Site Youtube Com for

The features that I want in a miter saw stand are:

  • #1 – Plenty of support for the boards being cut – no more cantilevering an 8′ board off of the small miter saw table!
  • Useful space – room for my tape measure and plans, but I want to keep the cut space clear (I have a clutter problem).
  • Room for a vacuum
  • Measuring guide for easy repeat cuts.
  • Mobile

the 1 last update 2020/08/04

This post contains some affiliate links for your convenience. Click here to read my full disclosure policy.

I’m excited with the result, it has TONS of storage with the two 4′ cabinets and two 2′ shallow drawers. It is quite large because it has 4′ on each side of the miter saw. If you don’t want a cabinet that large, the plans can be easily modified to only 2′ on each side of the saw.

This mobile miter saw station and storage unit calls for 3 sheets of 3/4″ birch plywood (about $50 each) and 1 sheet of 1/4″ plywood (about $12).  It includes the Kreg Precision Trak and Stop Kit on top of the fence to make repeat cuts nice and easy.  Did I mention, I’m so excited…what an upgrade!

I did customize the miter saw station for my Dewalt Miter Saw, but it should work with any miter saw. The plans note to measure the saw width, table height and how far the miter arm swings.

I’ve teamed up again with Buildsomething.com to bring you the free plans including the supply list, cut list and step by step instructions.  Buildsomething is Kreg’s new DIY project plan site with hundreds of free plans.  BuildSomething is a great community resource for woodworkers and DIY’ers, that may not have a site of their own, to share the plans they’ve created online.  Shared plans don’t have to be computer generated, even hand sketches will work. (click on link or sketch to be directed to the plans)

Grab the free building plans at BuildSomething! <–click here

Notes about the build:

I rarely ask my husband for help on projects, but when I do, it’s usually to help me cut down full sheets of plywood on the table saw.  He doesn’t really like to help cut full sheets because it’s a little stressful, if the plywood sheet starts going a little crooked then it can get bound up and that’s not good.  So getting a Rip Cut, may possibly be a marriage saver 🙂 Now I can cut down full sheets of plywood by myself!!!

I like using the Rip Cut, but there is one flaw, it can only cut up to 2′ wide. So if you need to cut the center of the plywood sheet you are SOL. To solve that issue, Kreg now has the Accu-Cut which is a simple guide that you just place on the plywood (no clamps, it has a rubber bottom). You use the same sled thing attached to your circular saw for the Rip Cut and the Accu-cut!

Once the plywood is down to manageable pieces, I still like to cut the exact sizes on my table saw. I do have building buddies that don’t use a table saw and build everything with the Rip cut/Accu-cut.

Setting up the Accu-Cut

It took me a few minutes to get the Accu-Cut assembled and ready to go.

First you attach the two 2′ tracks together with the provided bars and set screws.

Baby Rocking Chair Plans Site Youtube Comhow to Baby Rocking Chair Plans Site Youtube Com for Then you put the sled on the miter saw, this takes a bit of patience. You need to center the blade in the sled slot, set the right side position stop (gray block) and snug the little swing arms with set screws. The swing arms help hold the circular saw base to the sled.

Finally you adjust for zero clearance (see set up guide) and you’re ready to go.  Just remember, this isn’t a track saw, it’s really a fancy and handy ‘guide’ for your circular saw.  I’m really happy with the results.

Baby Rocking Chair Plans Site Youtube Comhow to Baby Rocking Chair Plans Site Youtube Com for Once you get the 1 last update 04 Aug 2020 the plywood sheets cut up, you’re halfway there!Once you get the plywood sheets cut up, you’re halfway there!

A couple of things to think about when you’re building the miter saw station, is your miter saw swing arm and table height.  If your miter saw arm swings beyond the miter saw base you’ll want to make sure you have enough room for it to swing fully right or left.

The plans allow for this, but you’ll want to know how much your saw swings to make sure there is enough room.

the 1 last update 2020/08/04   

Thanks for pinning!

Baby Rocking Chair Plans Site Youtube Comhow to Baby Rocking Chair Plans Site Youtube Com for

This building plan was sponsored by Buildsomething.com, all opinions and ideas are 100% my own.

Baby Rocking Chair Plans Site Youtube Comhow to Baby Rocking Chair Plans Site Youtube Com for Related